[Aleksey-MS]

Remote Install - Scania Multi, SDP3, SDP2, XCOM, BNS II Service Tool (BST)

Scania Multi 10.2021 online (via remote desktop) 12 months - $135
Scania Multi 10.2021 online (via remote desktop) 3 months - $59
Scania Multi 10.2021 online (via remote desktop) 1 month - $35

Scania Multi 04.2024 - $190
Scania Multi 2022 - $65
Scania Multi 2020 - $35
Scania Multi is a car dealership aftermarket service. The program contains a catalog for the selection of spare parts and electronic manuals for repair and maintenance. Scania Multi works by VIN code and uses only the last 7 digits to decrypt the wines of a bus or truck. In the program there is a search by the part number, you can find out its applicability, as well as get information about the re-release of parts.

[MHHAVTO registration required. HERE]

Scania SDP3 2.61.1.5 for Trucks + Buses (with keygen) - $600
Scania SDP3 2.61.1.5 for Trucks (with keygen) - $500
Scania SDP3 2.58.3 Truck, Bus, Marine (with keygen) - $299
Scania SDP3 2.61.1 Truck, Bus, Marine - $155
Scania SDP3 2.54 for Truck and Bus (with keygen) - $155
Scania SDP3 2.48 2021 - $35

SDP3 - Scania Diagnos + Programmer 3 (SDP3) software is designed for the diagnosis of Scania trucks and Scania industrial and marine engines. Connection to the electronic control units is done using the Scania VCI 2 or Scania VCI 3 interfaces. Depending on the version of the program, it supports work with all Scania trucks manufactured from 2004 to the present day.

[MHHAVTO registration required. HERE]

Scania Flasher Master unlimited time - $2755
Scania Flasher Master 1 year access - $1699
Scania Flasher Master 3 month access - $845
Scania Flasher Master 1 month access - $365

This software for read and write flash file for Scania ECU, with this software you don't need to use any extra tools and can use only Scania VCI2 or VCI3.
1 year access has 10 tokens-numbers for writing, reading and saving in the program. You can read from ECU and write on COO7 COO8 EMS S6 S7 S8 OPC TMS ECC.
3 and 1 months has less tokens.

Scania XCOM - $29
Scania XCOM - is a diagnostic tool to read, save, and modify ECU data such as trouble codes, parameters, statistic data etc. VCI2/VCI3 interface is used to connect to ECU via CAN protocol.

Supported modification of ECU data of the following types:

• EMS – Engine management system
  
• GMS – Gearbox management system
  
• RET – Retarder system
  
• AWD – All-wheel drive system
  
• CLS – Clutch Control
  
• EEC – Exhaust Emission Control
  
• COO (COO7) – Coordinator
  
• BWS (BCI1) – Bodywork system.
  

[MHHAVTO registration required. HERE]

Scania Developer (CDEV - ECOM - XCOM) - $299
Scania CDEV supports the following operations:

• Read ECU ID, data, parameters, fingerprint.
  
• Read and erase DTC.
  
• SparePart program all systems.
  
• Gather all data for field test functions.
  
• Load, modify, compare SOPS files.
  

Scania ECOM - is a program that, together with the VCI2, enables the communication between your PC and the control unit (EMS S6) on the engine.

You can carry out the following operations with ECOM:

• Read stored fault codes and Freeze Frames.
  
• Clear inactive fault codes.
  
• Read information about stored working cycles.
  
• Measure internal variables such as the engine speed, pressure, temperature and save them to a file.
  
• Program certain parameters.
  

Scania BNS II Service Tool (BST) - $39
Scania BNS II Service Tool (BST) is a PC-based diagnostic program for troubleshooting and programming of the electrical system in the bodywork of Scania OmniCity, OmniLink, and Citywide buses.

[MHHAVTO registration required. HERE]

Scania SOPS - $59
The program encrypts/decrypts SOPS files (contains data on parameters and specifications of all blocks of trucks or buses). Files can be downloaded using Scania VCI2.

Scania SOPS Editor Euro-6 2022 Unlimited - $570
Supports EURO 6 Scania Sops File Encryptor/Descriptor.

• Disable AdBlue
  
• Disable EGR
  
• Disable Immobilizer
  
• Change VIN
  
• Disable Nox Control
  
• Disable Torque Reduction NOx Control
  
• Disable Modify more than 300 other parameters and more
  

[*]

Scania AdBlue Off Remover with short instructions - $45


Scania IMMO Pin Code Decryption 4.02 (activation 1 PC) - $165
It works with - ASSY, COO6, COO7, COO8, EMS S6/S7/S8/EMD1, LAS1/LAS2

Need it? Write to me to discuss.