[Aleksey-MS]

Remote Install - Scania Multi, SDP3, SDP2, XCOM, BNS II Service Tool (BST)

Scania Multi 10.2021 online (via remote desktop) 12 months - $135
Scania Multi 10.2021 online (via remote desktop) 3 months - $59
Scania Multi 10.2021 online (via remote desktop) 1 month - $35

Scania Multi 04.2024 - $190
Scania Multi 2022 - $65
Scania Multi 2020 - $35
Scania Multi is a car dealership aftermarket service. The program contains a catalog for the selection of spare parts and electronic manuals for repair and maintenance. Scania Multi works by VIN code and uses only the last 7 digits to decrypt the wines of a bus or truck. In the program there is a search by the part number, you can find out its applicability, as well as get information about the re-release of parts.

[MHHAVTO registration required. HERE]

Scania SDP3 2.61.1.5 for Trucks + Buses (with keygen) - $600
Scania SDP3 2.61.1.5 for Trucks (with keygen) - $500
Scania SDP3 2.58.3 Truck, Bus, Marine (with keygen) - $299
Scania SDP3 2.61.1 Truck, Bus, Marine - $155
Scania SDP3 2.54 for Truck and Bus (with keygen) - $155
Scania SDP3 2.48 2021 - $35

SDP3 - Scania Diagnos + Programmer 3 (SDP3) software is designed for the diagnosis of Scania trucks and Scania industrial and marine engines. Connection to the electronic control units is done using the Scania VCI 2 or Scania VCI 3 interfaces. Depending on the version of the program, it supports work with all Scania trucks manufactured from 2004 to the present day.

[MHHAVTO registration required. HERE]

Scania XCOM - $29
Scania XCOM - is a diagnostic tool to read, save, and modify ECU data such as trouble codes, parameters, statistic data etc. VCI2/VCI3 interface is used to connect to ECU via CAN protocol.

Supported modification of ECU data of the following types:

• EMS – Engine management system
  
• GMS – Gearbox management system
  
• RET – Retarder system
  
• AWD – All-wheel drive system
  
• CLS – Clutch Control
  
• EEC – Exhaust Emission Control
  
• COO (COO7) – Coordinator
  
• BWS (BCI1) – Bodywork system.
  

[MHHAVTO registration required. HERE]

Scania Developer (CDEV - ECOM - XCOM) - $299
Scania CDEV supports the following operations:

• Read ECU ID, data, parameters, fingerprint.
  
• Read and erase DTC.
  
• SparePart program all systems.
  
• Gather all data for field test functions.
  
• Load, modify, compare SOPS files.
  

Scania ECOM - is a program that, together with the VCI2, enables the communication between your PC and the control unit (EMS S6) on the engine.

You can carry out the following operations with ECOM:

• Read stored fault codes and Freeze Frames.
  
• Clear inactive fault codes.
  
• Read information about stored working cycles.
  
• Measure internal variables such as the engine speed, pressure, temperature and save them to a file.
  
• Program certain parameters.
  

Scania BNS II Service Tool (BST) - $39
Scania BNS II Service Tool (BST) is a PC-based diagnostic program for troubleshooting and programming of the electrical system in the bodywork of Scania OmniCity, OmniLink, and Citywide buses.

[MHHAVTO registration required. HERE]

Scania SOPS - $59
The program encrypts/decrypts SOPS files (contains data on parameters and specifications of all blocks of trucks or buses). Files can be downloaded using Scania VCI2.

Scania SOPS Editor Euro-6 2022 Unlimited - $570
Supports EURO 6 Scania Sops File Encryptor/Descriptor.

• Disable AdBlue
  
• Disable EGR
  
• Disable Immobilizer
  
• Change VIN
  
• Disable Nox Control
  
• Disable Torque Reduction NOx Control
  
• Disable Modify more than 300 other parameters and more
  

[*]

Scania AdBlue Off Remover with short instructions - $45


Scania IMMO Pin Code Decryption 4.02 (activation 1 PC) - $165
It works with - ASSY, COO6, COO7, COO8, EMS S6/S7/S8/EMD1, LAS1/LAS2

Need it? Write to me to discuss.